To
Top

HEMEL® Fiber Cement Paint-Opaque

Water-based opaque fiber cement paint that allows board to breathe

  • Opaque
  • Water repellent
  • Allows board to breathe
  • Durable and resistant to exterior weather conditions and UV resistant
  • Lead-free
  • Does not crack, peel or blister
  • Environmentally friendly
  • Ready to use
White(Polar White):
104,95-TL /2,5 lt + VAT
569,95-TL / 15 lt + VAT
Red Ochre:
109,95-TL /2,5 lt + VAT
599,95-TL / 15 lt + VAT
** Upon request, special colors can be produced using the NCS and RAL color charts.

Find a Store

General Features:

  • Opaque
  • Water repellent
  • Allows board to breathe
  • Durable and resistant to exterior weather conditions and UV resistant
  • Lead-free
  • Does not crack, peel or blister
  • Environmentally friendly
  • Ready to use

Where to Use:

  • Fiber cement boards

Ambalaj Boyutları:

  • 2,5 L.
  • 15 L.
(*) Upon request, special colors can be produced using the NCS and RAL color charts.
  • White

    White

  • Red Ochre

    Red Ochre

  • Sınırsız Renk

    Sınırsız Renk Seçeneği

Warning

The colors are intended to approximate the final color. To see the final color, it is recommended to apply the coating on the board to be actually used.

Coverage:

  • 1 L. covers 5 m² with 2 coats

Surface Preparation:

  • Sand HEMEL Fiber Cement Primer coated surface with sandpaper #180/220.
  • Thoroughly clean the generated dust.

Application:

  • The product is ready to use and does not require thinning. (At very high temperatures 10% drinking water may be added).
  • Stir the product thoroughly before use and check its homogeneity. Repeat this process during the application
  • Apply the product in 2 coats by a brush or roller and wait 16 hours between coats.
  • Perform a slight sanding with a sandpaper #180/220 between coats.
  • Apply in the direction of board grain to get a homogeneous look.
  • Wait 16 hours for complete dry.

Maintenance (when the same product had been used before):

  • Do not apply the product directly on pre-coated surfaces.
  • Clean the surface completely from dirt and perform a slight sanding.
  • Thoroughly clean the generated dust.
  • Repeat same process as described in “Application” with 1 or 2 coats depending on weathering.
  • Inspect annually and maintain as required.

Instructions:

  • FOR EXTERIOR USE ONLY.
  • Keep product closed when not in use.
  • The general application temperature of the product is between 15oC to 25oC at a relative humidity range of 40-65%.
  • Do not apply the product under direct sunlight or rain.
  • The product should be protected from freezing and stored at temperatures between 5°C to 35°C.
  • Painting tools should be cleaned with soap and plenty of warm water after application.

Safety Precautions:

  • USE WITH ADEQUATE VENTILATION.
  • KEEP OUT OF REACH OF CHILDREN.
  • Do not transfer contents to other containers for storage.
  • Do not use empty plastic cans for other purposes.
  • To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying.
  • Avoid contact with eyes and skin.
  • Wash hands after using.
  • FIRST AID: In case of eye contact, flush thoroughly with large amounts of water. Get medical attention if irritation persists. If swallowed, call Poison Control Center, hospital emergency room, or physician immediately.
  • Dispose of contents/plastic cans in accordance with national regulations.
  • Please refer to the Safety Data Sheet (SDS) of the product for health and safety information.