HEMEL^® Universal Stain

• 

  SA 1119 - White

• 

  SA 1151 - Chestnut

• 

  SA 1121 - Teak

• 

  SA 1111 - Pale Walnut

• 

  SA 1190 - Mahogany

• 

  SA 1188 - Brown Walnut

• 

  SA 1184 - Brenner Walnut

• 

  SA 1192 - Walnut

• 

  SA 1166 - Green

Önemli Not

Используемое количество:

• 1 л в 1 слой покрывает 10-12 м2

Surface Preparation:

• Remove any dirt, oil and wood dust from the surface.
• New Wood Surfaces:
  • Sand the surface with sandpaper #80/120.
  • Thoroughly clean the generated dust.
• Old Uncoated Wood Surfaces:
  • Sand the weathered surface with sandpaper #80/120.
  • Thoroughly clean the generated dust.
• Coated Wood Surfaces:
  • Do not apply the product on pre-coated surfaces.
  • Remove the old paint/varnish from the surface completely with a sandpaper.
  • Thoroughly clean the generated dust.

Application:

• The product is ready to use and does not require thinning.
• Stir the product thoroughly before use and check its homogeneity. Repeat this process during the application.
• Apply the product in 1 coat by brush, cloth or dipping and wait 4-6 hours for complete dry.
• Apply in the direction of wood grain to get a homogeneous look.
• At extremely hot weathers you may add HEMEL Stabilizer by 2-3% to extend open time (drying time).
• For interior use decorative finish, apply HEMEL Varnish for Interior, HEMEL Home, HEMEL Heavy Traffic Parquet Varnish or HEMEL Ultramat as topcoat.
• For exterior use UV protection and decorative finish, apply HEMEL Varnish for Exterior or Hickson Decor® Aqua Industrial-Varnish VA10XX/VA11XX as topcoat.

Maintenance (when the same product had been used before):

• Do not apply the product on pre-coated surfaces.
• Remove the old stain/varnish from the surface completely with a sandpaper.
• Thoroughly clean the generated dust.
• Repeat same process as described in “Application”.
• Inspect annually and maintain as required.

Instructions:

• Keep product closed when not in use.
• The general application temperature of the product is between 15oC to 25oC at a relative humidity range of 40-65%.
• The moisture content of the wood should be max. 20% for exterior.
• Do not apply the product under direct sunlight or rain.
• Do not apply linseed oil, basecoat/primer, yacht varnish before or after HEMEL Universal Stain applied surfaces.
• To provide a long lifetime protection against decay, apply HEMEL Timbercare Aqua on untreated softwoods and wait 24 hours before applying HEMEL Universal Stain.
• The same product can be purchased in 15 L. cans as Hickson Decor® Aqua Industrial-Stain.
• The product should be protected from freezing and stored at temperatures between 5°C to 35°C.
• Painting tools should be cleaned with soap and plenty of warm water after application.

Safety Precautions:

• OIL SOAKED FABRIC CAN BE SELF IGNITING. FABRICS SHOULD BE COMPLETELY SOAKED IN WATER AND DISPOSED OF AFTER BEING USED.
• USE WITH ADEQUATE VENTILATION.
• KEEP OUT OF REACH OF CHILDREN.
• Do not transfer contents to other containers for storage.
• Do not use empty plastic cans for other purposes.
• To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying.
• Avoid contact with eyes and skin.
• Wash hands after using.
• FIRST AID: In case of eye contact, flush thoroughly with large amounts of water. Get medical attention if irritation persists. If swallowed, call Poison Control Center, hospital emergency room, or physician immediately.
• Dispose of contents/plastic cans in accordance with national regulations.
• Please refer to the Safety Data Sheet (SDS) of the product for health and safety information.