HEMEL® Yacht Varnish

Лак глянцевый на основе растворителя
- Прозрачный
- Глянцевый
- С повышенной устойчивостью против УФ-лучей
- Безупречное распределение по поверхности
- Гибкость
- Водооталкиваемость
- Без свинца
- Готов для применения
**,**-TL / 0,75 lt+ VAT
**,**-TL / 2,5 lt+ VAT
**,**/ 15 lt*+VAT
Find a Store
Общие характеристики:
- Прозрачный
- Глянцевый
- С повышенной устойчивостью против УФ-лучей
- Безупречное распределение по поверхности
- Гибкость
- Водооталкиваемость
- Без свинца
- Готов для применения
Область применения:
- Все виды дерева в наружных помещениях, кроме пола
- Деревянные поверхности катеров, находящиеся выше уровня воды
Упаковка:
- 0,750 л
- 2,5 л
- 15 л (изготовляется под заказ)
Данная продукция является бесцветной и не имеет цветовую гамму.
Hemel Products Catalogue
Hemel_Product_Catalogue.pdfSDS-Hemel Yacht Varnish
SDS-Hemel-Yacht-Varnish.pdfTDS-HEMEL Yacht Varnish
TDS-HEMEL-Yacht-Varnish-en.pdfИспользуемое количество:
- 1 л покрывает в 1 слой поверхность площадью 12-14 м2
Surface Preparation:
- Remove any dirt, oil and wood dust from the surface.
- Sand the surface with sandpaper #80/120.
- Thoroughly clean the generated dust.
- Sand the weathered surface with sandpaper #80/120.
- Thoroughly clean the generated dust.
- Do not apply the product directly on pre-coated surfaces.
- Remove the old paint/varnish from the surface completely with a sandpaper.
- Thoroughly clean the generated dust.
Application:
- The product is ready to use and does not require thinning.
- Stir the product thoroughly before use and check its homogeneity.
- Apply the product in 3 coats by brush and wait 24 hours between coats.
- Perform a slight sanding with sandpaper #180/220 between coats.
- Wait 24 hours for complete dry.
- Apply in the direction of wood grain to get a homogeneous look.
Maintenance (when the same product had been used before):
- Do not apply the product directly on pre-coated surfaces.
- Clean the wood surface completely from dirt and oil and perform a slight sanding.
- Thoroughly clean the generated dust.
- Repeat same process as described in “Application” with 1 or 2 coats depending on weathering.
- Inspect annually and maintain as required.
Instructions:
- FOR EXTERIOR USE ONLY.
- NOT SUITABLE FOR FLOORINGS
- Keep product closed when not in use.
- The general application temperature of the product is between 15oC to 25oC at a relative humidity range of 40-65%.
- The moisture content of the wood should be max. 20%.
- Do not apply the product under direct sunlight or rain.
- Do not apply linseed oil, basecoat/primer or after HEMEl Yacht Varnish applied surfaces.
- To provide a long lifetime protection against decay, apply HEMEL Timbercare Aqua on untreated softwoods and wait 24 hours before applying HEMEL Yacht Varnish.
- The product should be stored at temperatures between 5°C to 35°C.
- Painting tools should be cleaned with mineral spirits after the application.
Safety Precautions:
- USE WITH ADEQUATE VENTILATION.
- KEEP OUT OF REACH OF CHILDREN.
- Do not transfer contents to other containers for storage.
- Do not use empty plastic cans for other purposes.
- To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying.
- Avoid contact with eyes and skin.
- Wash hands after using.
- FIRST AID: In case of eye contact, flush thoroughly with large amounts of water. Get medical attention if irritation persists. If swallowed, call Poison Control Center, hospital emergency room, or physician immediately.
- Dispose of contents/plastic cans in accordance with national regulations.
- Please refer to the Safety Data Sheet (SDS) of the product for health and safety information.