Hemel Wood Oil 2C Oak

Tips

THERE IS A RISK OF SELF-FLAMMING IN LUBRICATED CLOTH. AFTER USE, THE CLOTHES MUST BE DISPOSED OF AFTER COMPLETELY WETTED WITH WATER.

The application method and quantities specified in the Technical Data Sheet of the product should be followed while applying.

Floor applications should be started first from parts such as edges and skirtings.

The 15-minute period expected after the product is applied is important because; During this period, HEMEL Wood Oil 2C product completely penetrates the surface by forming a chemical bond with the wood cells. Since the product is used with the hardener, after 15 minutes, it will be more and more difficult to remove the excess product remaining on the surface as time progresses and an oil film will begin to form on the surface.

Apply the product to the surface with circular movements, so that when applied, the product will better penetrate the veins of the wood.

We recommend that you use no more than 150 grit sanding units in the sanding process to prepare the surface before application. Especially in applications made on hardwood species, wood cells and pores over 150 grit sanders will not have enough clearance to absorb the product.

To be able to apply in maximum quantity with the product, we recommend applying with the pad machine. In this way, HEMEL Wood Oil 2C product will penetrate the wood better and the surface can be lubricated up to 50 square meters with a 1 liter product.

When mixing the product with its hardener, attention should be paid to the specified 20% ratio. For use below or above this ratio, the surface strength of the product will be affected differently. These mentioned rates are a result of our R & D studies and experience in wood.

We recommend that the surface be wiped with cellulosic thinner and wait until it dries before the application to be made on wood species containing high amounts of tannin, oil, and sap such as chestnut, iroko.

The most important feature of HEMEL Wood Oil 2C product is that it offers regional maintenance. When maintenance is desired, if the depth of the scratch is too high, sanding with 180-220 grit sandpaper should be done throughout the scratch and follow the instructions.

You can apply as specified. If the scratch is not too deep, you can perform maintenance by following the instructions with the product of the same color as the color you have used without polishing sandpaper.

If you do not prefer a natural and matte appearance and want a more shiny and smooth surface, you can apply the product in 2 layers. In this application, 24 hours after the completion of the first coat application, you can apply the second coat as specified in the application instructions by sanding with 180, 220, 320, or 400 grit sandpaper according to your preference.

If you are going to apply on soft trees such as Pine, without pouring the product on wood, cloth, brush, etc. we recommend that you apply the material by dipping it into the product. In this way, when applied by pouring the product directly on soft trees, because the absorbency of the Woods is high, there may be more absorption in the area where the product is poured, and color differences may occur on the surface due to this.

Problems and solutions

Spontaneous flame of the cloth used in the application.

• When applying oil-based products, in cases where cloth, sponge, felt, etc. are used, there is a possibility that the materials used spontaneously ignite, especially in hot weather. To prevent this, these materials that come into contact with oil after use should be completely wetted with water and then disposed of.

Freezing of the hardener left in the packaging after use

The problem is that the hardener gets air. The hardener of the product will start to freeze in the range of about 4-6 hours when it comes into contact with air. After your application is complete, make sure that the cover of the hardener is closed so that it does not receive air. In addition, in cases where a very small amount of hardener remains in the package, contact with the air can be minimized by transferring it to a smaller package so that there is no air gap on the hardener.

Freezing of the product after preparing the mixture

Causes of the Problem:

• The product hardens as a result of the chemical reaction of A and B components. This reaction takes place at a certain time. Under normal conditions, the life of HEMEL Wood Oil 2C Part A and Part B mixture is approximately 4-6 hours.

Solution:

• The mixture should be used within the specified period and care should be taken to prepare the mixture as much as the amount to be used. The life of the mixture may change depending on the ambient temperature and humidity.

Frequently Asked Questions

How long can I work after mixing two-component products?

You should consume two-component parquet varnishes within 2 hours and HEMEL Wood Oil 2C within 4-6 hours. Therefore, prepare only the amount of mixture you will use.

Which product should I use for old-style flooring?

You can use our oil-based and two-component HEMEL Wood Oil 2C product if you want not to spoil their natural appearance and protect your parquets. Apart from that, you can use any HEMEL water-based parquet polish.

I want to have a wooden ladder, which product would you recommend on it?

We recommend you use HEMEL Deck Oil on your outdoor wooden stairs.

If seasonal care is not a problem for you, you can apply it in HEMEL Exotic Oil.

On your indoor stairs, you can use our water-based parquet varnishes or our oil-based HEMEL Wood Oil 2C product.

What does natural oil mean?

Petroleum-derived oils (naphtha), polymerized oils, and natural oils are used in many oil paints and industries. Natural oils mentioned here refer to oils obtained from vegetable products such as linseed, tung fruit, soybean, and cotton.

Can I use it on kitchen counters?

 In areas that are likely to be in contact with water, such as kitchen and bathroom countertops, and where a lot of cleaning agents can be used during the day, we recommend that the application should be done with a brush or the product should be applied in 2 layers at 24 hours.

Can it be used on epoxy-containing log tables?

 You can safely use it on log tables containing epoxy, so you can both ensure that the epoxy surface shines and protect your wood against liquids by feeding it. In addition, you can maintain your old tables with Wood Oil 2C, depending on the conditions of use, which were previously applied with Wood Oil 2C.

Safety Precautions:

• WARNING: OIL SOAKED CLOTH USED FOR THE APPLICATION CAN BE SELF-IGNITING. CLOTH SHOULD BE COMPLETELY SOAKED IN WATER AND DISPOSED OF AFTER BEING USED.
• USE WITH ADEQUATE VENTILATION.
• KEEP OUT OF REACH OF CHILDREN.
• Do not transfer contents to other containers for storage.
• Do not use empty plastic cans for other purposes.
• To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying.
• Avoid contact with eyes and skin.
• Wash hands after using.
• FIRST AID: In case of eye contact, flush thoroughly with large amounts of water. Get medical attention if irritation persists. If swallowed, call Poison Control Center, hospital emergency room, or physician immediately.
• Dispose of contents/plastic cans in accordance with national regulations.
• Please refer to the Safety Data Sheet (SDS) of the product for health and safety information.

What is Wood Oil?

Wood oil penetrates the wood and leaves a natural look. Wood is prevented from rotting thanks to the wood-care oil's water repellent feature. You can feel its essence when you touch the wood by preserving the natural texture of hardwoods such as solid wood furniture, wooden countertops, wooden parquet and laminated parquet. While protecting the wood from external factors, it is necessary to care with wood oil to preserve its naturalness.

Wooden table, log table products are almost a lifetime. After simple sandpaper and natural oil care which you can do by yourself, they can have the perfect look like the first day.

What Does Wood Oil Do?

Although wood is a very elegant and high-quality material, needs to be protected very well. Decay and cracking may occur if you do not apply maintenance at certain intervals in the use of wooden countertops, wooden furniture and wooden parquet. Wood oil steps in to prevent rotting and protects the wood without losing its core texture.

Wood oil for the care of wooden furniture, wooden countertops, wooden parquet

Beeswax, oiled or wax-coated wooden furniture, wooden parquet and wooden countertops should be oiled at least once a year. In this way, the dry and dull appearance of the items is removed and your items gain a new look.

Single-component Hardwax Oil, which is a combination of natural Carnauba wax and natural oils produced by Hemel group for interior woods, and two-component, solvent-free wood oil, Hemel Wood Oil 2C will be the best wood care oil options for your wooden furniture and parquet. Although it is a wood oil that does not form a film layer, it also protects your wooden items against abrasion and scratches.

How to Clean Wooden Furniture?

If the wood is polished and finished, you can clean it with a clean cloth. The cloth you will use for wood cleaning and wood care should be a soft and at the same time slightly damp cloth. If the tree is painted, it is necessary to clean the wood with softwood oil and then apply wood polish to moisten it.

Furniture oil, wax, or polish treatment of wood are important in maintaining your furniture's shine and providing water repellency. Dampen at least once a month to prevent furniture from daily wear, cracking. You may also want to lubricate a new or used piece of furniture that looks dry.

You should protect wooden furniture and wood flooring from chemical cleaning products and liquids such as coffee, wine, water. Modern wooden furniture can be cleaned with a slightly damp towel with little soap. As antique furniture may have a more delicate surface, it would be appropriate to test it on a small area first and continue cleaning according to the result.

You should not place dishes, hot pans, hot pots on wooden countertops, laminated parquet, solid wood furniture.