Primetex Green

Solvent-based classic wood stain
Campaign
  • Features
  • Comments (0)
  • FAQ
  • Document
  • Application
  • Safety Precautions
  • Videos
  • Suggestion Box
  • Information
  • General Features
    • Silky glossy finish
    • Reduces moisture uptake
    • Minimizes crack formation
    • Water repellent
    • Resistant to UV and exterior weather conditions
    • Transparent and nine semi-transparent color options
    • Ready to use
    Where to use
    • Suitable for all exterior wood except floors
    • Doors and window joinery
    • Shutters
    • Claddings
    • Fences
    • Pergolas
    • Balcony railings
    • Roof fringes
    Packaging
    • 0,750 L.
    • 2,5 L.
    • 15 L. (Upon request)
    Dış Mekan İçindir
    Exterior
    Zeminde Uygulanmaz
    Not to be applied on decks/floors.
    Uv Dirençli
    Uv Resistant
    Fırça İle Uygulanır
    Apply with brush
    Önce Karıştırınız
    Stir well before use
    1 Lt-2 Katta 6-7 m2
    1 Lt covers 15-20 m2 in 2 coats
    Kabarma Yapmaz
    Do not crack or blister.


    Warning:     The colors shown here are applied on pine and intended to approximate the final color. The color and the gloss obtained will vary according to the type, texture, and absorbency of the wood. Film thickness and the number of coats applied will also affect the result. To see the final color, it is recommended to apply the product on the wood to be used.

  • PDF icon.png (4 KB) Safety Data Sheet (SDS)
    PDF icon.png (4 KB) Technical Data Sheet (TDS)
    PDF icon.png (4 KB) EN71-3 Toy Safety Certificate
  • Coverage:
    • 1 L. covers 15-20 m² with two coats

    Surface Preparation:

    • Remove any dirt, oil, and wood dust from the surface.

    New Wood Surfaces:

    • Sand the surface with sandpaper #80/120.
    • Thoroughly clean the generated dust.

    Old Uncoated Wood Surfaces:

    • Sand the weathered surface with sandpaper #80/120.
    • Thoroughly clean the generated dust.

    Coated Wood Surfaces:

    • Do not apply the product directly on pre-coated surfaces.
    • Remove the old paint/varnish from the surface completely with sandpaper.
    • Thoroughly clean the generated dust.

    Application:

    • The product is ready to use and does not require thinning. (In scorching weather, it can be diluted with thinner up to 5% maximum).
    • Stir the product thoroughly before use and check its homogeneity. Repeat this process during the application.
    • Apply the product in 2 coats by brush and wait 6-8 hours between coats.
    • Perform a slight sanding with sandpaper #180/220 between coats.
    • Apply 1 or 2 coats of the product with a cloth for coloring, depending on your preference. Applying a top coat to the product is recommended for long-term protection and a decorative appearance.
    • Wait 12 hours for complete drying.
    • Apply in the direction of the wood grain to get a homogeneous look

    Maintenance (when the same product had been used before):

    • Do not apply the product directly on pre-coated surfaces.
    • Clean the wood surface entirely from dirt and oil and perform a slight sanding.
    • Thoroughly clean the generated dust.
    • Repeat the process described in “Application” with 1 or 2 coats depending on weathering.
    • Inspect annually and maintain as required.

    Instructions:

    • FOR INTERIOR AND EXTERIOR USE.
    • NOT SUITABLE FOR FLOORINGS.
    • Keep product closed when not in use.
    • The general application temperature of the product is between 15°C to 25°C at a relative humidity range of 40-65%.
    • The moisture content of the wood should be max. 20%.
    • Do not apply the product under direct sunlight or rain.
    • Do not apply linseed oil, basecoat/primer, or yacht varnish before or after the product applied surfaces.
    • To provide extended lifetime protection against decay, apply Prime Wood Preserver on untreated softwoods and wait 24 hours before applying the product.
    • Since the clear color option does not contain pigment, it is not resistant to sunlight (UV). It is recommended to use Clear on Prime Decorative Wood Colorant as a topcoat for exterior uses.
    • The product should be stored at temperatures between 5°C to 35°C.
    • Painting tools should be cleaned with mineral spirits after the application.

  • Safety Precautions:

    • USE WITH ADEQUATE VENTILATION.
    • KEEP OUT OF REACH OF CHILDREN.
    • Do not transfer contents to other containers for storage.
    • Do not use empty plastic cans for other purposes.
    • To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying.
    • Avoid contact with eyes and skin.
    • Wash hands after using.
    • FIRST AID: In case of eye contact, flush thoroughly with large amounts of water. Get medical attention if irritation persists. If swallowed, call Poison Control Center, hospital emergency room, or physician immediately.
    • Dispose of contents/plastic cans in accordance with national regulations.
    • Please refer to the Safety Data Sheet (SDS) of the product for health and safety information.
  • • What Does Wood Stain Do?

    Wood Stain is a liquid solution used as a protective layer that prevents the wood from moistening and abrasion and increases its durability against external factors.
    The protective layer function is the most familiar feature of varnish. It is applied to wood as a preservative. It also makes long-used wooden surfaces and items look new. The moisture of the wood is prevented with water repellent wood stain. Wood stain also protects the wood against UV rays.

    Wood Stain Types
    Wood Stains are divided into water-based and solvent-based wood stains.

    Differences Between Water-Based Wood Stain and Solvent-Based Wood Stain:
    The service life of water-based and solvent-based Wood Stains is the same. Some differences are arising from the chemical structure of the raw materials used in its production.
    1. Water-based wood stain is odorless and also environmentally friendly. There is an odor of the thinner used in the production of solvent-based wood stains.
    2. Water-based wood stain gives a more natural finish, as wood absorbs more water-based varnish.
    3. Water-based wood stain dries faster.
    4. Water-based wood stain is safer for health as it has less VOC value.

    How to Choose Wood Stain?
    Wood Stains, which are sensitive to human and environmental health, nature friendly, do not contain heavy metal and lead, and have a toy safety certificate, should be preferred.
    It is also essential that it is a breathable Wood Stain, which extends the life of the wood.
    For exterior wood, it is essential to choose a wood stain that provides strong protection against sunlight and the Weatherproofing one.
    If you want the wood to preserve its natural texture and appearance, a translucent wood stain should be used.

    What is a breathable wood stain, and why is it important?
    Breathable paints and wood stains form a water-proof but water vapor-permeable layer on the applied surface. A small crack that may occur on the surface due to cracking or a small impact of the wood used outdoors due to precipitation and changes in the humidity in the air may cause the wood to become wet. The drying of this water, which soaks the wood under the layer, is essential for the life of the paint and wood. If the wood is wet for a long time, it causes both the paint to fall off and the wood to rot. Breathing wood stain/paint prevents this situation. It also penetrates the wood well and has the flexibility to work with the wood.

    Wood Stain Colors and Prices
    In Wood Staining application, if it is desired not to lose the natural texture of the wood, a semi-transparent Wood Stain should be used.
    Wood Stain colors have many different options. Grey wood stain, black wood stain, dark wood stain, dark oak wood stain, light oak wood stain, walnut wood stain, chestnut wood stain are some of the exterior wood stains. Click to see the rich water and solvent-based wood stain colors (color charts) produced by Hemel and learn about Wood Stain prices!

    Tips for an Exterior Wood Stain Application, How to stain wood?
    As a reply to the question ‘’How to stain wood?’’ here are all the details:
    When applying Wood Stain, sanding should be done between the layers to improve the final finish and ensure that the layers adhere to each other or get the paint's desired performance.
    For good wood protection, it is crucial to apply the product to the wood heads. Thus, water repellency is given to the heads of the wood that absorb the most water.
    Make sure that the edges of the wood you will wood stain are rounded. Wood Stain does not adhere sufficiently in sharp corners, and the film thickness remains weak. The possibility of getting water from this sharp corner of the wood may occur, causing the product to peel off.
    In exterior wood stain applications, the design of the wood details so that they do not accumulate on the surface where water will flow significantly increases the product's service life.
  • Features
    General Features
    • Silky glossy finish
    • Reduces moisture uptake
    • Minimizes crack formation
    • Water repellent
    • Resistant to UV and exterior weather conditions
    • Transparent and nine semi-transparent color options
    • Ready to use
    Where to use
    • Suitable for all exterior wood except floors
    • Doors and window joinery
    • Shutters
    • Claddings
    • Fences
    • Pergolas
    • Balcony railings
    • Roof fringes
    Packaging
    • 0,750 L.
    • 2,5 L.
    • 15 L. (Upon request)
    Dış Mekan İçindir
    Exterior
    Zeminde Uygulanmaz
    Not to be applied on decks/floors.
    Uv Dirençli
    Uv Resistant
    Fırça İle Uygulanır
    Apply with brush
    Önce Karıştırınız
    Stir well before use
    1 Lt-2 Katta 6-7 m2
    1 Lt covers 15-20 m2 in 2 coats
    Kabarma Yapmaz
    Do not crack or blister.


    Warning:     The colors shown here are applied on pine and intended to approximate the final color. The color and the gloss obtained will vary according to the type, texture, and absorbency of the wood. Film thickness and the number of coats applied will also affect the result. To see the final color, it is recommended to apply the product on the wood to be used.

    • Yorumlar (0)
  • FAQ
  • Document

    PDF icon.png (4 KB) Safety Data Sheet (SDS)
    PDF icon.png (4 KB) Technical Data Sheet (TDS)
    PDF icon.png (4 KB) EN71-3 Toy Safety Certificate
  • Application
    Coverage:
    • 1 L. covers 15-20 m² with two coats

    Surface Preparation:

    • Remove any dirt, oil, and wood dust from the surface.

    New Wood Surfaces:

    • Sand the surface with sandpaper #80/120.
    • Thoroughly clean the generated dust.

    Old Uncoated Wood Surfaces:

    • Sand the weathered surface with sandpaper #80/120.
    • Thoroughly clean the generated dust.

    Coated Wood Surfaces:

    • Do not apply the product directly on pre-coated surfaces.
    • Remove the old paint/varnish from the surface completely with sandpaper.
    • Thoroughly clean the generated dust.

    Application:

    • The product is ready to use and does not require thinning. (In scorching weather, it can be diluted with thinner up to 5% maximum).
    • Stir the product thoroughly before use and check its homogeneity. Repeat this process during the application.
    • Apply the product in 2 coats by brush and wait 6-8 hours between coats.
    • Perform a slight sanding with sandpaper #180/220 between coats.
    • Apply 1 or 2 coats of the product with a cloth for coloring, depending on your preference. Applying a top coat to the product is recommended for long-term protection and a decorative appearance.
    • Wait 12 hours for complete drying.
    • Apply in the direction of the wood grain to get a homogeneous look

    Maintenance (when the same product had been used before):

    • Do not apply the product directly on pre-coated surfaces.
    • Clean the wood surface entirely from dirt and oil and perform a slight sanding.
    • Thoroughly clean the generated dust.
    • Repeat the process described in “Application” with 1 or 2 coats depending on weathering.
    • Inspect annually and maintain as required.

    Instructions:

    • FOR INTERIOR AND EXTERIOR USE.
    • NOT SUITABLE FOR FLOORINGS.
    • Keep product closed when not in use.
    • The general application temperature of the product is between 15°C to 25°C at a relative humidity range of 40-65%.
    • The moisture content of the wood should be max. 20%.
    • Do not apply the product under direct sunlight or rain.
    • Do not apply linseed oil, basecoat/primer, or yacht varnish before or after the product applied surfaces.
    • To provide extended lifetime protection against decay, apply Prime Wood Preserver on untreated softwoods and wait 24 hours before applying the product.
    • Since the clear color option does not contain pigment, it is not resistant to sunlight (UV). It is recommended to use Clear on Prime Decorative Wood Colorant as a topcoat for exterior uses.
    • The product should be stored at temperatures between 5°C to 35°C.
    • Painting tools should be cleaned with mineral spirits after the application.
  • Safety Precautions

    Safety Precautions:

    • USE WITH ADEQUATE VENTILATION.
    • KEEP OUT OF REACH OF CHILDREN.
    • Do not transfer contents to other containers for storage.
    • Do not use empty plastic cans for other purposes.
    • To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying.
    • Avoid contact with eyes and skin.
    • Wash hands after using.
    • FIRST AID: In case of eye contact, flush thoroughly with large amounts of water. Get medical attention if irritation persists. If swallowed, call Poison Control Center, hospital emergency room, or physician immediately.
    • Dispose of contents/plastic cans in accordance with national regulations.
    • Please refer to the Safety Data Sheet (SDS) of the product for health and safety information.
  • Videos
    • Öneri Kutusu
You May Also Like
Prepared by  T-Soft E-Commerce.