Hemel PRO VA 1130 Industrial Clear Top-Coat

High-performance water-based industrial exterior clear topcoat

General Features

Transparent

Water repellent

UV absorber inside

Does not crack, peel, or blister

UV resistant if used with Hemel Pro HD or SA Wood Dye Series

Child safe (EN 71-3 Certified)

Allow breathing

Ready to use

Where to use

Suitable for all exterior wood except floors

Doors and window joinery

Shutters

Claddings

Fences

Pergolas

Balcony railings

Roof fringes

Packaging

15 L.

Exterior use only

Not to be applied on decks/floors.

Uv Resistant

Apply with a spray gun

Stir well before use

1 Lt covers 3-4 m2 in 2 coats

Does not crack or blister.

Warning: The product should be applied to Hemel Pro SA or HD Wood Dyes for maximum UV protection.
Safety Data Sheet (SDS)

Technical Data Sheet (TDS)

EN71-3 Toy Safety Certificate
Coverage:
- 1 L. covers 3-4 m² with two coats
Surface Preparation:
- Before applying the product, wait 4-6 hours for Hemel Pro SA or HD Wood Dyes or Hickson Decor® Aqua Industrial applied surface to dry.
Application:
- The product is ready to use and does not require thinning.
- Stir the product thoroughly before use and check its homogeneity. Repeat this process during the application.
- Apply the product in 2 coats by a spray gun (2,5-3 mm nozzle, min. 3 atm pressure) on Hemel Pro SA or HD Wood Dyes or Hickson Decor® Aqua Industrial-Stain without sanding (wet on wet) and wait 1,5-2 hours between coats.
- If a time of 3 hours is exceeded between coats for any reason, wait 24 hours and sand the surface with #220/240 sandpaper before applying the second coat.
- Wait 24 hours for complete drying.
- For the best result, slight sanding between coats is advised.
Maintenance (when the same product had been used before):
- Do not apply the product directly on pre-coated surfaces.
- Clean the wood surface entirely from dirt and oil and perform a light sanding.
- Thoroughly clean the generated dust.
- Repeat the same process as described in Application with 1 or 2 coats depending on weathering.
- Inspect annually and maintain as required.
Instructions:
- FOR EXTERIOR USE ONLY.
- NOT SUITABLE FOR FLOORINGS.
- Keep the product closed when not in use.
- The product's general application temperature is between 15°C and 25°C, with a relative humidity range of 40-65%.
- The moisture content of the wood should max 20%.
- Do not apply the product under direct sunlight or rain.
- Do not apply linseed oil, basecoat/primer, or yacht varnish before or after product-coated surfaces.
- To provide long-life protection against decay, apply HEMEL Timbercare Aqua on untreated softwoods and wait 24 hours before using the product.
- The product should be stored at temperatures between 5°C to 35°C.
- After application, painting tools should be cleaned with soap and plenty of warm water.
Safety Precautions:
- USE WITH ADEQUATE VENTILATION.
- KEEP OUT OF REACH OF CHILDREN.
- Do not transfer contents to other containers for storage.
- Do not use empty plastic cans for other purposes.
- To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying.
- Avoid contact with eyes and skin.
- Wash hands after using.
- FIRST AID: In case of eye contact, flush thoroughly with large amounts of water. Get medical attention if irritation persists. If swallowed, call Poison Control Center, hospital emergency room, or physician immediately.
- Dispose of contents/plastic cans in accordance with national regulations.
- Please refer to the Safety Data Sheet (SDS) of the product for health and safety information.

Features
General Features

Transparent

Water repellent

UV absorber inside

Does not crack, peel, or blister

UV resistant if used with Hemel Pro HD or SA Wood Dye Series

Child safe (EN 71-3 Certified)

Allow breathing

Ready to use

Where to use

Suitable for all exterior wood except floors

Doors and window joinery

Shutters

Claddings

Fences

Pergolas

Balcony railings

Roof fringes

Packaging

15 L.

Exterior use only

Not to be applied on decks/floors.

Uv Resistant

Apply with a spray gun

Stir well before use

1 Lt covers 3-4 m2 in 2 coats

Does not crack or blister.

Warning: The product should be applied to Hemel Pro SA or HD Wood Dyes for maximum UV protection.

Yorumlar (0)

FAQ
Document

Safety Data Sheet (SDS)

Technical Data Sheet (TDS)

EN71-3 Toy Safety Certificate
Application
Coverage:

1 L. covers 3-4 m² with two coats

Surface Preparation:

Before applying the product, wait 4-6 hours for Hemel Pro SA or HD Wood Dyes or Hickson Decor® Aqua Industrial applied surface to dry.

Application:

The product is ready to use and does not require thinning.

Stir the product thoroughly before use and check its homogeneity. Repeat this process during the application.

Apply the product in 2 coats by a spray gun (2,5-3 mm nozzle, min. 3 atm pressure) on Hemel Pro SA or HD Wood Dyes or Hickson Decor® Aqua Industrial-Stain without sanding (wet on wet) and wait 1,5-2 hours between coats.

If a time of 3 hours is exceeded between coats for any reason, wait 24 hours and sand the surface with #220/240 sandpaper before applying the second coat.

Wait 24 hours for complete drying.

For the best result, slight sanding between coats is advised.

Maintenance (when the same product had been used before):

Do not apply the product directly on pre-coated surfaces.

Clean the wood surface entirely from dirt and oil and perform a light sanding.

Thoroughly clean the generated dust.

Repeat the same process as described in Application with 1 or 2 coats depending on weathering.

Inspect annually and maintain as required.

Instructions:

FOR EXTERIOR USE ONLY.

NOT SUITABLE FOR FLOORINGS.

Keep the product closed when not in use.

The product's general application temperature is between 15°C and 25°C, with a relative humidity range of 40-65%.

The moisture content of the wood should max 20%.

Do not apply the product under direct sunlight or rain.

Do not apply linseed oil, basecoat/primer, or yacht varnish before or after product-coated surfaces.

To provide long-life protection against decay, apply HEMEL Timbercare Aqua on untreated softwoods and wait 24 hours before using the product.

The product should be stored at temperatures between 5°C to 35°C.

After application, painting tools should be cleaned with soap and plenty of warm water.
Safety Precautions
Safety Precautions:
- USE WITH ADEQUATE VENTILATION.
- KEEP OUT OF REACH OF CHILDREN.
- Do not transfer contents to other containers for storage.
- Do not use empty plastic cans for other purposes.
- To avoid overexposure, open windows and doors or use other means to ensure fresh air entry during application and drying.
- Avoid contact with eyes and skin.
- Wash hands after using.
- FIRST AID: In case of eye contact, flush thoroughly with large amounts of water. Get medical attention if irritation persists. If swallowed, call Poison Control Center, hospital emergency room, or physician immediately.
- Dispose of contents/plastic cans in accordance with national regulations.
- Please refer to the Safety Data Sheet (SDS) of the product for health and safety information.
Videos